Purchase RainKit^® without Barrels

This light-weight wrench is designed specifically for barrel caps ("bungs") for a watertight seal on every barrel. It has a variety of levers and knobs for various size bungs, and for removing bung covers.

Use a pipe-cutter for clean, easy, and accurate cuts to PVC pipe. Your BlueBarrel System® specifies 3/4" pipe, but this cutter will work with plastic pipe up to 1" in diameter.

Use this tool to drill your tee-in ports to install BlueBarrel's signature "under-plumbing."

This specialty drill bit will drill clean vent holes with minimal plastic "snow."

This hole saw includes an arbor and pilot bit for easy use with any drill. You will need this tool to drill the inlet hole to connect your downspout diverter to your BlueBarrel System®.

This hole saw includes an arbor and pilot bit for easy use with any drill. Order this tool to install your downspout diverter in a PLASTIC downspout. If you have a metal downspout, order the 2-1/8-in Hole Saw FOR METAL (below).

This hole saw includes an arbor and pilot bit for easy use with any drill. Order this tool to install your downspout diverter in a METAL downspout. If you have a plastic downspout, order the 2-1/8-in Hole Saw FOR PLASTIC (above).

The Leaf Eater Advanced offers a robust, easy-clean screen-filter for water entering your rainwater catchment system. Includes 0.955mm stainless steel mosquito proof screen, and is highly recommended if you get any leaf or debris accumulation in your gutters. It will also prevent gravel chips from asphalt shingles from entering your barrels. Leaf eaters are recommended by most rainwater harvesting professionals over a "first flush" device. A first flush will lead to increased sediment loads if not maintained properly, and it may divert too much water away from your barrels in light rains. The Leaf Eater, by contrast, intercepts debris without inhibiting the flow of water to your barrels - and it is much easier to keep clean. This product works with 2" x 3" or 3" x 4" rectangular downspouts. It also works with round pipe, 3" in diameter, and can be adapted to other round pipe sizes with standard bushings. The leaf eater requires that you cut your downspout, so if you have a downspouts of a different dimension, you can replace the lower segment with 2" x 3" material for compatibility with the Leaf Eater AND BlueBarrel's standard downspout diverter, or with any size that fits one of our downspout diverter options.

If you have more than 2.5' between your downspout and barrels, you will need a longer inlet hose. Please note this product replaces the original diverter hose rather than extending it, so you will need to measure the full distance between your downspout and barrels. THIS PRODUCT IS SOLD BY THE FOOT, and shipped as one continuous length. Enter the total number of feet you need for the purchase quantity. (The material is easy to cut if you need multiple segments.)

This diverter kit handles inflow and overflow automatically. Kit includes a rubberized diverter head that seals inside 2" x 3" downspouts. Kit also includes a 31" flexible inlet hose, watertight hose seal, inlet screening, stainless steel screws, and illustrated installation instructions. (For spans longer than 31", order inlet hose by the foot from this menu of accessories.) REQUIRED FOR INSTALLATION: 1-1/2" Hole Saw and 2-1/8" Hole Saw, available in our TOOLS menu. Some diverter kit parts are available for individual sale, click SHOW RAINKIT PARTS.

The RainRouter Selector Valve Kit is compatible with the FlexiFit downspout diverter, which is included in all of our DIY RainKits® (or sold separately above). The selector valve inserts into the diverter head to send rain in two directions. Connect to two rain barrels, two garden hoses, or one of each! A simple turn-dial allows you to send water in one direction or the other, or both at once. The "off" setting keeps water flowing down your downspout as normal. Assembly includes selector valve and 2 multi-hose adapters. NOTE: The selector valve pairs with a FlexiFit Downspout Diverter head. These are included in our DIY RainKits. If you don't have one, select a round or rectangular diverter from our accessories menu.

This piece is recommended in areas with hard freezes where rain barrels are disconnected during the winter. (No need to disconnect for light freezes!). Insert the Winter Cover into the diverter hole to seal off the downspout for the winter. In the spring, simply remove the Winter Cover and re-insert the downspout diverter. Select this item if you have rectangular downspouts. RECOMMENDED: Order the 1-1/2" Expandable Twist Plug (below) to seal the hole in your barrel while barrels are disconnected in winter.

Tapered rubberized plug inserts into holes around 1-1/2" in size. Twist the stainless-steel handle to expand the plug for a watertight seal. DIMENSIONS: 1-15/64" at the narrow end, tapering up to 1-17/32" at the broad end. This size fits the 1-1/2" inlet hole in the BlueBarrel System. Order along with the Winter Cover (above) to seal up your system during winter disconnect. Or use it as a goof-plug if you want to drill a new inlet.

The Tank Gauge by Rain Harvesting monitors the level in your BlueBarrel System® with an easy-to-read dial. It is quick and easy to install, and uses a non-numbered "Empty-to-Full" scale so it will work with tanks of any size (up to 100" in height). With the BlueBarrel System's unique under-plumbed design, your water level will be the same in all barrels, so you only need one Tank Gauge for a multi-barrel system. Installation instructions specify a 1-1/4-in Hole Saw (available here in our online store under "TOOLS"). A 1-1/2-in Hole Saw will also work.

Most BlueBarrel Systems® consist of one long row of barrels. The Multi-Row Connection allows you to install double-rows. Order one Multi-Row Connection for each block of barrels that you will be doubling up (usually one per system). Order two Multi-Row Connections to install a triple-row. This item includes all necessary connection fittings, an extra isolation valve, and a a multi-row plumbing configuration diagram.

These thick, insulated bags slip right over the outlets on your rain barrels (or any outdoor faucet!) for a neat-looking and user-friendly approach to winter freeze protection. Reflective strip provides visibility, and velcro cinch allows for easy access to the tap. Faucet cover is made with high-quality, three-layer anti-freeze and waterproof material. Product dimensions: 8.5" H x 6.1" W.

This streamlined 100-micron drip irrigation filter has a slim profile and a fine mesh to keep drip emitters from clogging. It connects easily to the drain valve included in your RainKit®, or any standard 3/4" hose valve. All drip irrigation options in our accessories menu are fit-ready for this filter. If you want more than one drip irrigation or soaker hose connection on a BlueBarrel System®, you will need to order an Extra Drain Assembly for each additional drip filter. (Replacement filter cartridges also available from this accessories menu.)

This battery-operated, hose-end timer is ideal for gravity-fed systems with low pressures. The 2-Dial Timer easily attaches to the drain valve or spigot on your BlueBarrel System®, or any other standard rain tank or barrel - (recommended in conjunction with the Streamlined Irrigation Filter). FEATURES INCLUDE: Easy-to-set-dials; Manual on/off setting; Low battery indicator; Intervals: From every hour, to once a week; Duration: Select 1, 3, 10, 15, 20, 30, 45, 60, 90 or 120 min; Pressure Range: 0 - 125 PSI; Batteries: Two AA alkaline batteries (not included); Manufacturer Warranty: 12 months. (Please note, most irrigation timers do not work with non-pressurized rain barrels--this one does!)

This is a complete kit assembled just for use with the BlueBarrel Rainwater Catchment System®, or any non-pressurized rain barrels, tanks, or cisterns. It includes parts to cover up to 250 square-feet or 10 planted rows. KIT INCLUDES: 3/4-inch swivel fitting to connect with Drip Irrigation Filter (filters sold separately above); 50 feet ½ inch drip tubing; 100 feet ¼ inch gravity-feed dripline with 12-inch predrilled emitter spacing; (10) barbed dripline connectors; (10) goof plugs; (2) elbows; (1) coupler; (2) figure-8 hose-ends; (5) stakes for ½-in tubing; (10) stakes for 1/4-in dripline; and an easy-grip hole punch to customize your dripline placement - instructions included. EXTRA PARTS AVAILABLE - CLICK BUTTON BELOW TO VIEW INDIVIDUAL PARTS.

This is a complete kit assembled just for use with the BlueBarrel Rainwater Catchment System®, or any non-pressurized rain barrels, tanks, or cisterns. It includes parts to cover up to 50 plants in a layout with up to 5 rows. KIT INCLUDES: 3/4-inch swivel fitting to connect with Drip Irrigation Filter (filters sold separately, above); 100 feet of ½ inch drip tubing; (50) adjustable gravity feed button drippers; (4) elbows; (4) tees; (1) coupling; (5) figure-8 hose-ends; (10) goof plugs; (5) stakes for ½ inch tubing; and an easy-grip hole punch to customize your emitter placement - instructions included. EXTRA PARTS AVAILABLE - CLICK BUTTON BELOW TO VIEW INDIVIDUAL PARTS.

This soaker hose is not like others! It is specifically designed for low-pressure and no-pressure water sources like gravity-fed rain barrels. 50' each. Link multiple hoses together (maximum 100' run on a flat site for gravity-fed applications). Comes with 200-mesh filter. Maximize the life span and effectiveness of hose by keeping it completely shaded (e.g. under a hedge row).